Descriptions
Rectangle Compartment Side Way Action Type Jig has two types. One is left compartment side way jig, another is right compartment side way jig. The jig has fixed screen. It is available in separating metallic ores, such as tungsten and gold placer deposits as well as beneficiated tin ore, which not only can be separated fine materials, but coarse also. The largest feed size is 6-8mm but it can be 12mm in few cases.
Rectangle Compartment Side Way Action Type Jig is mainly composed of jig box, drive device, water distribution, diaphragm and bibcock. There are two jig buckets with different sizes and each diaphragm is divided into jig area and diaphragm area by clapboard. The rubber diaphragm pumping to make medium (water) moving is the jigging course. The triangle belt drives big belt pulley by electromotor so connecting rod of the eccentric gear and rocker are up and down moving. Another connecting rod is connected with the rubber diaphragm which is moving up and down to jig.
Based on the size of ore, we can change the stroke of connecting rod and choose different stroke to make the best jigging effect. The method of altering stroke per minute is to exchange a smaller belt pulley but there are two strokes per minute: 322r/m; 420r/m. The method of choosing stroke is to loose bolt and screw cap, take out bowel and move the relative place between eccentric adjusting sieve and eccentric shaft so there are 11 different strokes (0-25.3mm).
Because of a sieve added on the working screen, the jig can be processed the uneven sizes of material. (note: the sieve can be requested to supply or not). After the feed ores are sent to jig chamber, the ores are separated to different layers in the medium by the pulsation of diaphragm. The light but weight is sank to the tank of jig bucket through the spaces of materials of artificial bed layer and its sieve holes but the coarse but light is washed to the discharge end of screen by medium. Because the back jig chamber is lower 50mm than front jig chamber, the light ores is overflowed through front jig chamber to the back chamber and jigged again. If needed, the place of end plate can be adjusted to control the discharge amount. The concentrate in tank can be discharged by discharge tube regularly.
Technical Specifications
Model |
Jig chamber |
Jig Area (m2) |
Feeding Size (mm) |
Capacity (t/h) |
Stroke (mm) |
Stroke Per Minute (r/min) |
Hutch Water |
Water Pressure (kilo/cm2) |
Power |
Weight (kg) |
300×450 |
2 |
0.27 |
-12 |
3-6 |
0-26 |
322 |
2-4 |
1-1.5 |
1.1 |
745 |
|
1000×1000 Below Diaphragm Jig |
2 |
2 |
1-5 |
10-25 |
0-26 |
200-350 |
60-80 |
0.6-2 |
1.5 |
1700 |
Mineral Processing Equipment is a kind of large porous ceramic disc which is fired by inorganic membrane making technology.gold/copper/coal/iron/hematite/chrome ore dressing equipment (jigging plant) has following characteristics:large filter area.high intensity and even aperture.Besides,the aperture size can be adjusted according to actual demands.Mineral Processing Equipment is alumina,it has good resistance to acid and alkali.After a period of application,the ceramic filter board can be cleaned by cycle reverse cleaning,ultrasonic and chemical cleaning agent and so on,to let the boards work with high efficiency.
JHBHHHHG
Mineral Processing Equipment is a kind of equipment which combines the characteristics of spiral concentrator, spiral chute, shaking table and centrifugal concentrator. gold/copper/coal/iron/hematite/chrome ore dressing equipment (jigging plant) is the best equipment for mining and mineral processing, especially for beach, riverside, sand beach and Creek channel. Mineral Processing Equipment has the advantages of reasonable structure, simple installation, less land occupation, simple operation, stable ore dressing, gold/copper/coal/iron/hematite/chrome ore dressing equipment (jigging plant) clear ore classification, large processing capacity, high efficiency, high concentration ratio of ore dressing, high recovery rate and reliable operation.
JKJBHGB