Product Description
Introduction
jaw crusher with crushing ratio, product material uniformity, simple structure, reliable, simple maintenance, operating costs and other economic characteristics. Widely used in mining, smelting, building materials, roads, railways, water conservancy and chemical and other departments, broken compressive strength of not more than 320 MPa of various stone.
Use range
1, the series crusher is mainly used for metallurgy, mining, chemical, cement, construction, refractory materials and ceramics and other industrial sectors for the broken and crushed all kinds of hard minerals and rocks.
2, the series crusher is most suitable for crushing compressive strength of not more than 320MPa (MPa) of various soft and hard ore, the maximum mass of broken material shall not be greater than the technical parameters specified in the table.
Schematic
jaw crusher structure mainly frame, eccentric shaft, large pulley, flywheel, moving jaw, side guards, brackets, elbow rear seat, gap screw, reset spring, fixed jaw plate and movable jaw plate, etc. The brackets also play an insurance role.
Working principleThe series of crusher work for the curved extrusion type, its working principle is: the motor drive belt and pulley, through the eccentric shaft to move the jaw up and down movement, when the moving jaw up when the angle between the brackets and moving jaw larger To promote the moving jaw plate to the fixed jaw plate close to the same time the material is crushed or split, to break the purpose; when the moving jaw down, the brackets and moving jaw angle becomes smaller, moving jaw plate in the rod, the role of spring , Leaving the fixed jaw plate, at this time has been broken material from the crushing chamber discharge. With the continuous rotation of the motor and crusher motor jaw for cyclical movement crushing and excretion of materials, to achieve mass production.
| Model | Motor Power (Kw) | Capacity(t/h) | Rotor Speed(r\min) | Max Feeding Size(mm) | Discharge Size(mm) |
| PE250×400 | 18.5 | 5-20 | 280-320 | 220*380 | 30-120 |
| PE300×500 | 22 | 8-40 | 280-300 | 270*480 | 35-130 |
| PE400×600 | 30 | 12-50 | 280-300 | 320*530 | 35-140 |
| PE400×600 | 30 | 15-60 | 280-300 | 350*580 | 40-150 |
| PE500×750 | 55 | 30-112 | 250-280 | 450*730 | 50-180 |
| PE600×900 | 55-75 | 50-190 | 250-275 | 550*850 | 80-200 |
| PE750×1060 | 110-132 | 100-280 | 250-275 | 650*1010 | 90-250 |
| PE900×1200 | 132-160 | 200-500 | 220-250 | 750*1100 | 120-300 |
| PE1000×1200 | 132-160 | 300-600 | 200-250 | 850*1100 | 200-320 |
| PE1200×1500 | 160-185 | 400-800 | 180-220 | 1020*1400 | 200-350 |
| PEX250×750 | 22 | 12-35 | 280-350 | 210 | 25-60 |
| PEX250×1000 | 37 | 16-50 | 280-350 | 210 | 25-60 |
| PEX250×1200 | 45 | 20-60 | 280-350 | 210 | 25-90 |
| PEX350×750 | 37 | 16-50 | 280-350 | 300 | 30-100 |
| PEX150×250 | 5.5 | 2-5 | 350-400 | 130*230 | 10-40 |
Maintenance methodIn order to ensure the jaw crusher normal work, in addition to correct operation, must be planned maintenance,Including routine maintenance checks, minor repairs, repair and overhaul.
(1) minor repair: the main contents include inspection and repair adjustment device, high-speed discharge port gap, the wear of the liner U-turn or replacement. Maintenance of transmission parts, lubrication systems and replacement of lubricants. Minor repair period of 1-3 months or so.
(2) in the repair: In addition to the small repair of all the work, but also including the replacement of thrust plate, liner, check and repair pad and so on. The repair cycle is generally about 1-2 years.
(3) overhaul: In addition to the repair of all the work, but also including the replacement or turning eccentric shaft and moving jaw mandrel, casting the upper part of the rod of the Babbitt, replace or repair the wear parts. Overhaul of the cycle is generally about 5 years.
Boot maintenanceFirst, the boot before the equipment inspection
1, check the rack, pulley, flywheel parts of the Department of any loose;2, check the jaw teeth plate. Moving jaw teeth plate, side guards are intact, bolts are fastened, thrust plate with or without cracks, spring rods and springs are intact;
3, check the safety railing, safety cover and ore chute, etc. are intact;
4, check whether the motor anchor bolts, motor wiring, the operation box of the instrument is intact, whether the voltage within the specified range;
5, check the crushing chamber with or without large pieces of ore and debris, V-belt is intact, tension is appropriate.
Second, boot
1, must confirm the equipment and no one around the work in order to start the device;
2, after starting the host, the first observation of the equipment is running smoothly, the voltage, the current normal no abnormal sound, pulley and flywheel without loosening phenomenon, to the mine;
3, to the mine must be uniform, can not suddenly large and small, resulting in equipment load suddenly large and small, causing the belt slip pressure ore;
4, every half hour to observe the voltage and current conditions, with or without abnormal smell and ignition phenomenon, check the bearing temperature does not exceed 60 ℃
5, check the Department of the phenomenon of any loose bolts, racks, motor feet, whether the phenomenon of loose feet, rotating parts with or without noise.
Certifications
Contact meWelcome to Best price tire type mobile jaw crusher station for sale,jaw crusher machine with CE and ISO Approval. Our honour to be at your service.
Feel free to choose your expecting products, and mail/call if you are interested in our products.
we may need you to provide us some details for an accurate quotation.
1. What is the raw material do you want to process?
2. What is the handling capacity per hour do you need?
3. What is the max feeding size of the raw material?
4. What is the output size of the products?
5. Any other special requirements?
or Whatsapp/Best price tire type mobile jaw crusher station for sale,jaw crusher machine with CE and ISO Approval 0086 177 3727 7937
Best price tire type mobile jaw crusher station for sale,jaw crusher machine with CE and ISO Approval1684587018
Jaw Crusher Machine is fit for dry and wet sieving, classification of powdery, granular and filamentary materials and dehydration of materials. If fine sieving is required Best price tire type mobile jaw crusher station for sale,jaw crusher machine with CE and ISO Approval can be satisfied by adopting high-efficiency screen mesh-cleaning device to improve the sieving. For wet sieving Best price tire type mobile jaw crusher station for sale,jaw crusher machine with CE and ISO Approval is especially fit for separation of sludge (waste water) and preliminary compression of mixed matter of solid and liquid materials.
hhhghj
Jaw Crusher Machine can do according to customers special demands. We provide our customers with high-quality Jaw Crusher Machine, advanced production technology and perfect after-sales services.Best price tire type mobile jaw crusher station for sale,jaw crusher machine with CE and ISO Approval Our well-equipped facilities and excellent quality control throughout all stages of production enables us to guarantee total customer satisfaction.
YHAYAG